Exhibitor List
| Company | FLAME (SHANGHAI) ENVIRONMENTAL TECHNOLOGY CO., LTD. |
| Country | China |
| Products | Treatment of volatile organic compounds（VOCs) Desulphurization and denitrification Information technology Analysis and laboratory techniques Environmental monitoring techniques and equipment |
| Hall | E5 |
| Booth | F59 |
| Website | www.flametech.com.cn |
| Introduction | Flame Environmental Focused on the research and development of high-end environmental monitoring instruments and technological innovation. We have independently researched, developed, and produced in-situ direct insertion high-temperature flue gas NOx/O2 nitrogen oxide detectors that operate stably and reliably in online NOx monitoring for high-temperature boilers in major coal-fired power plants, steel mills, cement factories, and other industries. These products are utilized for precise ammonia injection control at the inlet and outlet of denitrification SCR systems. |
Products
| FT-NOx 5000 in-situ rapid analyzer for flue gas nitrogen oxide FT-NOX5000 in-situ rapid analyzer for flue gas nitrogen oxide, based on the principle of double-cell thick-film zirconia detector, does not need to add a nitrogen oxide conversion unit (molybdenum cage, NO 2 to No) , and is installed directly on the flue, the sample gas is inhaled into the measuring room for real-time measurement, no sampling pipeline, no condensation, rapid response, real-time and efficient detection, dual-detector switching, direct measurements of NOx nitrogen oxide and O2 content are available for on-line monitoring of flue gas emissions from high temperature boilers, denitrification control, precision ammonia injection and other DCS control systems, main features: 1, directly inserted into the flue, field measurement, without station room, air-conditioning room 2, built-in heater, can measure -15-300 degrees of flue gas, without sample gas extraction, condensation 3, double detectors continuous measurement, can set regular switching, long life, high reliability 4, large range, high precision 5, data real-time display, built-in embedded database, can access historical data 6, easy to install, easy to operate, no professional operation and maintenance 7, built-in gas timing blowing, long-term work without maintenance of 8,5-inch full-color touch screen, human-machine interface is good, simple Operation 9, support on-line whole process calibration 10, signal output: RS485,2-way 0-20mA, support 1-way alarm signal output |
 |
| D8100 environmental data acquisition and transmission instrument D8100 Environment-friendly data acquisition and transmission instrument is connected with meteorological parameter monitor, gas sensor, flue gas analyzer, CEMS instrument, temperature and pressure flow integrated machine, flue gas humidity meter, chromatograph, VOCs instrument, flowmeter, COD, PH, ammonia nitrogen, residual chlorine and other instruments through digital/analog signal interface, to collect real-time data of sensors and instruments. The instrument data collected in real time is transmitted to the platform through the network to realize the function of data collection and transmission. Applicable to: data collection and transmission of environmental monitoring, water conservancy, meteorology and other big data platforms Main features: 1. Comply with H/T212-2017 "Data Transmission Standard for On-line Automatic Monitoring (Monitoring) System of Pollution Sources" and IEC-104 regulations 2, 8 inch full color touch screen, good man-machine interface, simple operation 3, Using ARM9 processor, embedded operating system and embedded real-time database, stable and reliable operation 4, built-in memory, can store 3 million data, support manual and automatic data transmission 5, good compatibility, built-in mainstream instrument driver protocol, can be downloaded remotely 6, rich interface: equipped with 8 channels analog, 2 channels RS232, 4 channels RS485 digital data acquisition interface; 4-way switch input interface; 4 relay output interface 7, Built-in 4G communication module, support mobile/telecom/Unicom/environmental protection APN card, built-in 1 RJ45 interface, support a bit more transmission and remote parameter configuration 8. Installation mode: wall-mounted installation of cast aluminum shell IP65 protection 9, built-in lithium battery, in the case of external disconnect can maintain normal work |
 |
| D5100 environmental data acquisition and transmission instrument D5100 Environment-friendly data acquisition and transmission instrument is connected with meteorological parameter monitor, gas sensor, flue gas analyzer, CEMS instrument, temperature and pressure flow integrated machine, flue gas humidity meter, chromatograph, VOCs instrument, flowmeter, COD, PH, ammonia nitrogen, residual chlorine and other instruments through digital/analog signal interface, to collect real-time data of sensors and instruments. The instrument data collected in real time is transmitted to the platform through the network to realize the function of data collection and transmission. Applicable to: data collection and transmission of environmental monitoring, water conservancy, meteorology and other big data platforms Main features: 1. Comply with H/T212-2017 "Data Transmission Standard for On-line Automatic Monitoring (Monitoring) System of Pollution Sources" and IEC-104 regulations 2, 5 inch full color touch screen, good man-machine interface, simple operation 3, Using ARM9 processor, embedded operating system and embedded real-time database, stable and reliable operation 4, built-in memory, can store 3 million data, support manual and automatic data transmission 5, good compatibility, built-in mainstream instrument driver protocol, can be downloaded remotely 6, rich interface: equipped with 8 channels analog, 2 channels RS232, 2 channels RS485 digital data acquisition interface; 4-way switch input interface; 2 relay output interface 7, Built-in 4G communication module, support mobile/telecom/Unicom/environmental protection APN card, built-in 1 RJ45 interface, support a bit more transmission and remote parameter configuration 8. Installation mode: wall-mounted installation of cast aluminum shell IP65 protection 9, built-in lithium battery, in the case of external disconnect can maintain normal work |
 |
| S70 environmental protection data acquisition and transmission instrument S70 environmental protection data acquisition and transmission instrument through the digital/analog signal interface with meteorological parameter monitoring instrument, gas sensor, gas analyzer, CEMS instrument, temperature and pressure flow integrated machine, gas humidity meter, chromatograph, VOCs instrument, flowmeter, COD, PH, ammonia nitrogen, residual chlorine and other instruments connected to collect the real-time data of sensors and instruments. The instrument data collected in real time is transmitted to the platform through the network to realize the function of data collection and transmission. Applicable to: data collection and transmission of environmental monitoring, water conservancy, meteorology and other big data platforms Main features: 1. Comply with H/T212-2017 "Data Transmission Standard for On-line Automatic Monitoring (Monitoring) System of Pollution Sources" and IEC-104 regulations 2, 7 inch full color touch screen, good man-machine interface, simple operation 3, Using ARM9 processor, embedded operating system and embedded real-time database, stable and reliable operation 4, built-in memory, can store 3 million data, support manual and automatic data transmission 5, good compatibility, built-in mainstream instrument driver protocol, can be downloaded remotely 6, rich interface: equipped with 1 RS232, 2 RS485 digital volume acquisition interface 7, Built-in 4G communication module, support mobile/telecom/Unicom/environmental protection APN card, built-in 1 RJ45 interface, support a bit more transmission and remote parameter configuration 8. Installation mode: wall-mounted installation |
 |
| FT-NOx500 in-line high temperature nitrogen oxide analyzer FT-NOx500NOx Analyzer System High temperature type in-situ measurement method, based on the principle of double pool thick film zirconia detector, do not need to increase the nitrogen oxide conversion unit (molybdenum cage, NO2 to NO), directly the high temperature resistant detector probe into the chimney or pipeline real-time measurement, no sampling pipe, no extraction, condensation gas, rapid response, The detection is real-time and efficient, which can directly measure the concentration of NOx nitrogen oxides and O2 oxygen content Suitable for: VOCs online monitoring (FID) plus NOx factor online monitoring; On-line monitoring system for flue gas emission of high temperature boiler; DCS control system for denitration control, precision ammonia spray, etc. Main features: 1, directly inserted into the flue, field measurement, no station room, air conditioning room 2, can measure 500 degrees of high temperature flue gas, no sample gas extraction, condensation 3, large range, high precision 4. Real-time data display, built-in embedded database, historical data can be accessed 5, simple installation, convenient operation, no professional operation and maintenance 6, built-in timing back purging system, support built-in air source purging 7, 7 inch full color touch screen, good man-machine interface, simple operation 8, support online calibration 9, signal output: RS485, 2 0-20mA, support 1 alarm signal output |
 |
| In situ Direct Analyse NOx/O2 Analyzing Sytem The in-situ NOXO2 flue gas nitrogen oxide analyzer for coal-fired power plants is based on the principle of a double-cell thick-film zirconia detector, accurate on-line measurement of 1500 ppm nitrogen oxide and 25.0% oxygen in flue gas. It is suitable for: NOx detection of combustion equipment such as a side and B side of denitrification unit, high temperature boiler, denitrification system, desulphurization unit, diesel engine and marine engine exhaust; Detection of combustion tail gas in steel, cement, power plant and other industries; real-time concentration detection of Nox and O2 in SCR Inlet and SCR outlet, calculation of denitrification removal rate; multi-industry application of precise ammonia injection scenario. Main features: 1. Double-cell thick-film zirconia detector 2. Large range, high precision 3,5 inch full-color touch screen, friendly man-machine interface, easy to operate, 2, easy Installation 4, online calibration 5, installation mode: In-situ Direct Measurement 6, sampling mode: ejection sampling 7, signal output: RS485,2-way 4-20mA 1-way alarm signal output 8, built-in embedded database, real-time display of NOx and O2 concentration data, can be derived from historical data |
 |
| D7100 environmental data acquisition and transmission instrument D7100 environment-friendly data acquisition and transmission instrument is connected with meteorological parameter monitor, gas sensor, flue gas analyzer, CEMS instrument, temperature and pressure flow integrated machine, flue gas humidity meter, chromatograph, VOCs instrument, flowmeter, COD, PH, ammonia nitrogen, residual chlorine and other instruments through digital/analog signal interface, to collect real-time data of sensors and instruments. The instrument data collected in real time is transmitted to the platform through the network to realize the function of data collection and transmission. Applicable to: data collection and transmission of environmental monitoring, water conservancy, meteorology and other big data platforms Main features: 1. Comply with H/T212-2017 "Data Transmission Standard for On-line Automatic Monitoring (Monitoring) System of Pollution Sources" and IEC-104 regulations 2, 7 inch full color touch screen, good man-machine interface, simple operation 3, Using ARM9 processor, embedded operating system and embedded real-time database, stable and reliable operation 4, built-in memory, can store 3 million data, support manual and automatic data transmission 5, good compatibility, built-in mainstream instrument driver protocol, can be downloaded remotely 6, rich interface: equipped with 8 analog, 1 RS232, 2 RS485 digital data acquisition interface; 2 relay output interface 7, Built-in 4G communication module, support mobile/telecom/Unicom/environmental protection APN card, built-in 1 RJ45 interface, support a bit more transmission and remote parameter configuration 8. Installation mode: wall-hanging/guideway installation |
 |
| FT-NOx100 nitrogen oxide detector FT-NOx100 flue gas nox analyzer is designed based on the principle of double pool thick film zirconia sensor, and can accurately measure nitrogen oxides of up to 1500ppm and oxygen of up to 25.0% in flue gas online. Suitable for: high temperature boiler and other combustion device NOx detection; Denitration system, desulfurization unit NOx detection; Diesel engine and Marine engine exhaust test; Detection of combustion exhaust gas in steel, cement, power plant and other industries; Real-time concentration detection of NOx and O2 at SCR inlet and outlet, calculation of denitration removal rate; Multi-industry application of precision ammonia spray scenario. Main features: 1, using double pool thick film zirconia sensor 2, large range, high precision 3, 5 inch full color touch screen, man-machine interface friendly, easy to operate, easy to install 4, can be calibrated online 5, installation mode: cabinet wall hanging 6, sampling method: pump suction extraction 7, signal output: RS485, 2 4-20mA 1 alarm signal output 8, built-in embedded database, real-time display NOx and O2 concentration data, historical data can be exported |
 |
| FT-NOx500s NOx/O2 Analyzer Sytem FT-NOx500s in-situ flue gas nitrogen oxide detector, based on the principle of double pool thick film zirconia detector, do not need to increase the nitrogen oxide conversion unit (molybdenum cage, NO2 to NO), directly into the detector probe into the chimney or pipeline real-time measurement, no sampling pipe, no extraction, condensation gas, rapid response, real-time detection efficient, The concentration of NOx nitrogen oxides and O2 oxygen content can be measured directly Suitable for: VOCs online monitoring (FID) plus NOx factor online monitoring; On-line monitoring system for flue gas emission of high temperature boiler; DCS control system for denitration control, precision ammonia spray, etc. Main features: 1, directly inserted into the flue, field measurement, no station room, air conditioning room 2, can measure 220 degrees of high temperature flue gas, no sample gas extraction, condensation 3, large range, high precision 4. Real-time data display, built-in embedded database, historical data can be accessed 5, simple installation, convenient operation, no professional operation and maintenance 6, built-in timing back purging system 7, 5 inch full color touch screen, good man-machine interface, simple operation 8, support online calibration 9, signal output: RS485, 2 0-20mA, support 1 alarm signal output |
 |
